Skip to main content

AP® Physics C: Electricity and Magnetism Unit 11 flashcardsElectric Circuits

42 cards · about 11 minutes for the whole deck

Flashcard drill

Space flips the card, arrow keys move, and keys 1 to 4 rate how well you knew it.

Position
1 / 42
Due
42
Mastered
0 / 42
Saved on this device · Sign in to sync

This card: New

Something wrong with this card?

What's wrong?

Please don't include personal details.

Flip the card before you rate it.

  • Electric current

    The rate charge passes through a cross section of a wire, I=dqdtI = \frac{dq}{dt}. One ampere is one coulomb per second. Current is a scalar, even though it has a direction along the wire.

    Topic 11.1: Electric Current

  • Conventional current

    The direction positive charge would move: out of a battery’s positive terminal. In metal wires the moving charges are really electrons, which drift the opposite way.

    Topic 11.1: Electric Current

  • Drift velocity

    The slow average velocity of charge carriers along a wire, often less than a millimeter per second. Each carrier moves fast and randomly, but the net drift is what makes current.

    Topic 11.1: Electric Current

  • Current from drift speed

    I=nqvdAI = nqv_dA: current equals carrier density × carrier charge × drift speed × cross-sectional area. A thinner wire with the same current needs a faster drift.

    Topic 11.1: Electric Current

  • Current density

    Current per unit area, a vector: J⃗=nqv⃗d\vec{J} = nq\vec{v}_d, in A/m². For a uniform current J=IAJ = \frac{I}{A}.

    Topic 11.1: Electric Current

  • Total current from a varying J

    When J changes across a wire, integrate over the area: I=∫J⃗⋅dA⃗I = \int \vec{J} \cdot d\vec{A}. For J(r) in a round wire use rings, dA=2πr drdA = 2\pi r\,dr.

    Topic 11.1: Electric Current

  • Electromotive force (emf)

    The potential difference a battery would supply with no current in it, written E\mathcal{E}. It’s what pushes charge around a circuit; despite the name, it isn’t a force.

    Topic 11.1: Electric Current

  • Closed circuit

    A complete conducting loop, so charge can flow all the way around it.

    Topic 11.2: Simple Circuits

  • Open circuit

    A circuit with a break in it, like an open switch, so no charge can flow around that path.

    Topic 11.2: Simple Circuits

  • Short circuit

    A path with no change in potential, like a bare wire across an element. Current takes it, and the elements it goes around get no current.

    Topic 11.2: Simple Circuits

  • Circuit schematic

    A diagram that uses standard symbols for batteries, resistors, bulbs, capacitors, inductors, switches and meters. An arrow drawn diagonally across a symbol means a variable element.

    Topic 11.2: Simple Circuits

  • Resistance

    How strongly an object opposes the flow of charge, in ohms (Ω). It depends on the object’s material and its shape.

    Topic 11.3: Resistance, Resistivity, and Ohm’s Law

  • Resistivity

    A property of a material (not its shape) that says how strongly it opposes current, in Ω·m. For a uniform wire R=ρℓAR = \frac{\rho \ell}{A}. A metal’s resistivity usually rises with temperature.

    Topic 11.3: Resistance, Resistivity, and Ohm’s Law

  • Resistance with varying resistivity

    If ρ changes along a uniform wire, add thin slices: R=∫ρ(x)A dxR = \int \frac{\rho(x)}{A}\,dx.

    Topic 11.3: Resistance, Resistivity, and Ohm’s Law

  • Field inside a current-carrying wire

    A potential difference across a conductor makes an electric field inside it, E=ρJE = \rho J. That field is what drives the current.

    Topic 11.3: Resistance, Resistivity, and Ohm’s Law

  • Ohm’s law

    ΔV=IR\Delta V = IR. It holds for ohmic materials, whose resistance stays the same whatever the current.

    Topic 11.3: Resistance, Resistivity, and Ohm’s Law

  • Ohmic material

    A material whose resistance stays constant, so its current–voltage graph is a straight line through the origin. A glowing bulb filament is a common non-ohmic example.

    Topic 11.3: Resistance, Resistivity, and Ohm’s Law

  • Current–voltage graph

    For an ohmic element, current versus potential difference is a straight line with slope 1R\frac{1}{R}. A curve that flattens means resistance is rising.

    Topic 11.3: Resistance, Resistivity, and Ohm’s Law

  • Electric power

    The rate an element transfers energy: P=IΔVP = I\Delta V, in watts (1 W = 1 J/s). For a resistor, P=I2R=(ΔV)2RP = I^2R = \frac{(\Delta V)^2}{R}.

    Topic 11.4: Electric Power

  • Bulb brightness

    A bulb glows brighter when it uses more power. To rank bulbs, compare I²R or (ΔV)²/R for each one.

    Topic 11.4: Electric Power

  • Energy used by a resistor

    For steady power, ΔE=PΔt\Delta E = P\Delta t; when the current changes, ΔE=∫P dt\Delta E = \int P\,dt. A resistor turns electrical energy into thermal energy (and light, in a bulb).

    Topic 11.4: Electric Power

  • Series connection

    Elements on one path with no branches: they carry the same current, and their potential differences add up to the total.

    Topic 11.5: Compound Direct Current Circuits

  • Parallel connection

    Elements on separate branches between the same two points: each has the same potential difference, and the branch currents add up to the total.

    Topic 11.5: Compound Direct Current Circuits

  • Equivalent resistance

    The single resistor that could replace a group. Series: Req=R1+R2+⋯R_{eq} = R_1 + R_2 + \cdots. Parallel: 1Req=1R1+1R2+⋯\frac{1}{R_{eq}} = \frac{1}{R_1} + \frac{1}{R_2} + \cdots, which is less than the smallest one.

    Topic 11.5: Compound Direct Current Circuits

  • Internal resistance

    A real battery acts like an ideal emf in series with a small resistor r. It wastes some energy inside the battery whenever current flows.

    Topic 11.5: Compound Direct Current Circuits

  • Terminal voltage

    The potential difference across a real battery’s terminals: ΔV=E−Ir\Delta V = \mathcal{E} - Ir. It equals the emf only when no current flows.

    Topic 11.5: Compound Direct Current Circuits

  • Ideal ammeter

    Measures current. It goes in series with the element and has zero resistance, so it doesn’t change the current it measures.

    Topic 11.5: Compound Direct Current Circuits

  • Ideal voltmeter

    Measures potential difference. It goes in parallel across the element and has infinite resistance, so no current flows through it.

    Topic 11.5: Compound Direct Current Circuits

  • Nonideal meters

    A real ammeter adds a little resistance, and a real voltmeter lets a little current through. Either way the meter changes the circuit it measures.

    Topic 11.5: Compound Direct Current Circuits

  • Kirchhoff’s loop rule

    The potential differences around any closed loop add to zero, ∑ΔV=0\sum \Delta V = 0. It comes from conservation of energy.

    Topic 11.6: Kirchhoff’s Loop Rule

  • Potential versus position in a loop

    A graph of potential as you travel around a loop: it jumps up by the emf across a battery, slopes down across each resistor, and is flat along ideal wires.

    Topic 11.6: Kirchhoff’s Loop Rule

  • Loop rule sign conventions

    Crossing a battery from − to + adds E\mathcal{E}. Crossing a resistor in the direction of the current subtracts IR; crossing it against the current adds IR.

    Topic 11.6: Kirchhoff’s Loop Rule

  • Kirchhoff’s junction rule

    The current into a junction equals the current out, ∑Iin=∑Iout\sum I_{in} = \sum I_{out}. It comes from conservation of charge.

    Topic 11.7: Kirchhoff’s Junction Rule

  • Solving a multi-loop circuit

    Guess a direction for each branch current, write junction equations and enough loop equations, then solve them together. A negative answer means that current runs opposite your guess.

    Topic 11.7: Kirchhoff’s Junction Rule

  • Capacitors in parallel

    Ceq=C1+C2+⋯C_{eq} = C_1 + C_2 + \cdots. Each capacitor has the same potential difference, so the charges add.

    Topic 11.8: Resistor-Capacitor (RC) Circuits

  • Capacitors in series

    1Ceq=1C1+1C2+⋯\frac{1}{C_{eq}} = \frac{1}{C_1} + \frac{1}{C_2} + \cdots. Each one holds the same charge, and CeqC_{eq} is smaller than the smallest capacitor.

    Topic 11.8: Resistor-Capacitor (RC) Circuits

  • RC time constant

    τ=RC\tau = RC, in seconds. A charging capacitor reaches about 63% of its final charge after one τ; a discharging one falls to about 37%.

    Topic 11.8: Resistor-Capacitor (RC) Circuits

  • Charging a capacitor

    Starting uncharged: q(t)=CE(1−e−t/RC)q(t) = C\mathcal{E}\left(1 - e^{-t/RC}\right) and I(t)=ERe−t/RCI(t) = \frac{\mathcal{E}}{R}e^{-t/RC}. The current is largest at the start.

    Topic 11.8: Resistor-Capacitor (RC) Circuits

  • Discharging a capacitor

    Through a resistor: q(t)=Q0e−t/RCq(t) = Q_0 e^{-t/RC}. The charge, the potential difference and the current all decay toward zero.

    Topic 11.8: Resistor-Capacitor (RC) Circuits

  • RC loop equation

    Kirchhoff’s loop rule for charging: E−Rdqdt−qC=0\mathcal{E} - R\frac{dq}{dt} - \frac{q}{C} = 0. Solving this differential equation gives the exponential curves.

    Topic 11.8: Resistor-Capacitor (RC) Circuits

  • Capacitor right after switching

    An uncharged capacitor acts like a plain wire at first: charge flows on and off its plates easily, and there is no potential difference across it.

    Topic 11.8: Resistor-Capacitor (RC) Circuits

  • Capacitor after a long time

    A fully charged capacitor acts like a break: no current flows in its branch, and its potential difference matches whatever it is connected across.

    Topic 11.8: Resistor-Capacitor (RC) Circuits