AP® Chemistry Unit 6 flashcardsThermochemistry
30 cards · about 8 minutes for the whole deck
Flashcard drill
Space flips the card, arrow keys move, and keys 1 to 4 rate how well you knew it.
- Position
- 1 / 30
- Due
- 30
- Mastered
- 0 / 30
This card: New
Flip the card before you rate it.
System and surroundings
The system is the part you're studying, like the reacting chemicals. The surroundings are everything else, like the water and the beaker.
Topic 6.1: Endothermic and Exothermic Processes
Exothermic
The system releases energy to the surroundings, so the surroundings warm up. ΔH is negative. Example: burning fuel.
Topic 6.1: Endothermic and Exothermic Processes
Endothermic
The system absorbs energy from the surroundings, so the surroundings cool down. ΔH is positive. Example: a cold pack.
Topic 6.1: Endothermic and Exothermic Processes
Heat (q)
Energy transferred because of a temperature difference. q is positive when the system gains heat and negative when it loses heat.
Topic 6.1: Endothermic and Exothermic Processes
Energy diagram
A diagram comparing the energy of reactants and products. Products lower means exothermic (ΔH < 0); products higher means endothermic (ΔH > 0).
Topic 6.2: Energy Diagrams
Enthalpy change (ΔH)
The heat absorbed or released by a process at constant pressure. Read it on an energy diagram as the products' level minus the reactants' level.
Topic 6.2: Energy Diagrams
Temperature
A measure of the average kinetic energy of a substance's particles. It is not the same thing as heat.
Topic 6.3: Heat Transfer and Thermal Equilibrium
Heat transfer
Energy flows from a hotter object to a cooler one as faster particles collide with slower ones and pass along kinetic energy.
Topic 6.3: Heat Transfer and Thermal Equilibrium
Thermal equilibrium
The point where two objects in contact reach the same temperature, so their particles have the same average kinetic energy and no net heat flows.
Topic 6.3: Heat Transfer and Thermal Equilibrium
Specific heat capacity (c)
The energy needed to raise 1 g of a substance by 1 °C. Water's is high, 4.18 J/(g·°C), so it warms up and cools down slowly.
Topic 6.4: Heat Capacity and Calorimetry
Molar heat capacity
The energy needed to raise 1 mole of a substance by 1 °C, in J/(mol·°C).
Topic 6.4: Heat Capacity and Calorimetry
q = mcΔT
Heat = mass × specific heat × temperature change. Use ΔT = final − initial, so a temperature drop gives a negative q.
Topic 6.4: Heat Capacity and Calorimetry
Calorimetry
Measuring heat flow from a temperature change. The heat the process gives off is absorbed by the water: q(process) = −q(water).
Topic 6.4: Heat Capacity and Calorimetry
First law of thermodynamics
Energy is conserved: it isn't created or destroyed, only moved around. Whatever energy the system loses, the surroundings gain.
Topic 6.4: Heat Capacity and Calorimetry
Enthalpy of fusion
The energy needed to melt 1 mole of a solid at its melting point. Water's is about 6.01 kJ/mol. Freezing releases the same amount.
Topic 6.5: Energy of Phase Changes
Enthalpy of vaporization
The energy needed to boil 1 mole of a liquid. Water's is about 40.7 kJ/mol at 100 °C. Condensing releases the same amount.
Topic 6.5: Energy of Phase Changes
Heating curve plateau
While a pure substance melts or boils, its temperature stays flat. The added energy goes into overcoming intermolecular forces, not into speeding particles up.
Topic 6.5: Energy of Phase Changes
Heat for a phase change
q = moles × molar enthalpy of the change. Melting 2.00 mol of ice takes 2.00 × 6.01 ≈ 12.0 kJ.
Topic 6.5: Energy of Phase Changes
Enthalpy of reaction
The heat released (negative) or absorbed (positive) at constant pressure when a reaction happens in the mole amounts shown in the balanced equation.
Topic 6.6: Introduction to Enthalpy of Reaction
Thermochemical equation
A balanced equation with its ΔH, like N₂ + 3H₂ → 2NH₃, ΔH = −92 kJ/mol. The ΔH goes with the coefficients as written.
Topic 6.6: Introduction to Enthalpy of Reaction
Scaling ΔH to amounts
Heat = (moles that react ÷ coefficient in the equation) × ΔH. Making 1 mol of NH₃ releases half of 92 kJ, or 46 kJ.
Topic 6.6: Introduction to Enthalpy of Reaction
Bond enthalpy
The energy needed to break one mole of a given bond in the gas phase. Breaking bonds always takes energy; forming them always releases it.
Topic 6.7: Bond Enthalpies
ΔH from bond enthalpies
ΔH ≈ Σ(bonds broken) − Σ(bonds formed). If the new bonds release more energy than the old bonds took to break, the reaction is exothermic.
Topic 6.7: Bond Enthalpies
Average bond enthalpy
Tabulated bond enthalpies are averages over many molecules, so ΔH values calculated from them are only estimates.
Topic 6.7: Bond Enthalpies
Standard enthalpy of formation (ΔH°f)
The ΔH for making 1 mole of a compound from its elements in their standard states, like H₂(g) + ½O₂(g) → H₂O(l).
Topic 6.8: Enthalpy of Formation
Standard state
The most stable form of a substance at 1 atm and the stated temperature, usually 25 °C: O₂(g), C(graphite), Br₂(l). Elements in their standard states have ΔH°f = 0.
Topic 6.8: Enthalpy of Formation
ΔH° from formation enthalpies
, with each value multiplied by its coefficient.
Topic 6.8: Enthalpy of Formation
Hess's law
If a reaction is the sum of several steps, its ΔH is the sum of the steps' ΔH values. It works because energy is conserved.
Topic 6.9: Hess's Law
Hess's law: reversing a step
Writing a reaction backward keeps the size of ΔH but flips its sign.
Topic 6.9: Hess's Law
Hess's law: scaling a step
Multiplying a reaction's coefficients by a number multiplies its ΔH by the same number. Halve the equation, halve ΔH.
Topic 6.9: Hess's Law